kechme93
kechme93
AnyOne going to Mustang Week 2014
Comments
-
Merry Christmas to all
-
How would (MATCHING #s) play into effect , after an accident? Example: If replacing a body panel due to an collision, with a very skilled Paint & Body person, paint entire vehicle, replace (ALL) vin labels with reproduction (then you have a …
-
I have not replaced any internals,but did have the same issue with my 92 GT and on my 93. Did manage to get the window back up, it is a very tight place to work,my advice to you is PATIENCE. I personally would not tear into the other one, as long as…
-
Interesting, I'm gonna need to get one before winter for sure,even though I start it often, it's kinda embarrassing to say, I've not had my car on the (ROAD) since May/013.
-
Thinking about purchasing one. Been told the (JR) is the best choice, not sure the difference between the two, besides the size.
-
GoodYear: GatorBack
-
Would have like to seen, more FoxBody attendees :-w
-
We are planning on Hooter's around 6 p.m. this evening.
-
Due to work, We are not going down until Thur. But could get together, to eat Tues evening.Exit (398 StrawPlains Exit) has good dining and Lodging????
-
Is there going to be any (GATHERING) points, along the way to Charlotte?
-
Here in East Tennessee the roads are basically covered in SALT/BRINE.
-
My Triple White, has a slightly discolored Top edge also.
-
My 93, has a slightly different shade of White
-
Heater Core FLUSH was a success. Blazing Hot Heat now!!!
-
In the Nov 2012 Muscle Mustangs & Fast Fords Mag- Page 132- A Triple White in the True Street competition averaged 16.51 NOT BAD
-
I very seldom let the 1/4 windows down anyway, even with the top down -for the very reason of (fearing they want go back up ). Imagine that
-
Both my 1/4 window motors went out today.I did manage to get them back up and in place.As for replacing them, I'm going to let them stay -(IN PLACE) for now. It's not for money reasons, it just really bothers me, when even a (NEW) part is so poorly …
-
Ron is a very knowledgeable guy and speaking of- if your reading this Ron please forgive me for not returning phone call I LOST your #
-
That was a pretty HARD HIT. The guy in the Vette's reaction was priceless
-
After searching the internet, it is not uncommon for the Upper Intake Bolts to lossen, due to Aluminum to Cast. Everytime I would replace a Part/Sensor- a (CODE) would disappear, But the PROBLEM wouldn't. I couldn't wait to fire the car up this m…
-
UPDATE!! After the purchase of an OBD1 scanner, I replaced an - Idle Air Control Valve/ Sensor, EGR Position Sensor, Egr Pressure Solenoid,Fuel Pump Relay and New Fuel Pump.In the end it was the (Upper Intake Gasket Leaking)
-
(ALL) the local autoparts stores in my area, say they can only pull codes on 1996 and newer vehicles. Dealership says no problem (BRINGER ON IN) but of course $ 110.00 +Tax
-
No codes have been pulled yet. It would be great to have one to read (BOTH) Early & Late Models, Reason be I have a 96 f150, 97Expedition, 92, 93 Mustang. Guess I need to do some HOMEWORK on these code scanners.
-
O2 sensors are pluged up/ Check engine light will come on if sitting in traffic - then turn off (No other time) I dont have a code scanner. Need to purchase one
-
Robert is was great talking to you @ show. Super nice Triple WHITE.
-
July 16th - 22nd 2012
-
Mine also, chip in Black Trim. Took a couple hours to get hood aligned correctly. I used a 4 inch level & a Marble. Probably a little over kill.
-
Hair drier & Fishing string - Heat the badge, try to wiggle or loosen by hand, to break the SEAL then while still applying heat, take fising string and Gently pull string between badge and surface.